manualshive.com logo in svg

Cisco MX200 G2, Руководство администратора

Поделиться
Скачать
Cisco MX200 G2 Скачать руководство пользователя страница 67

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.  

www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 

67

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Cameras Camera [1] Gamma Level

By setting the Gamma Level you can select which gamma correction table to use. This 

setting may be useful in difficult lighting conditions, where changes to the brightness setting 

does not provide satisfactory results. Requires the Cameras Camera [n] Gamma Mode to be 

set to Manual.

Requires user role: USER
Default value: 0

Value space: Integer (0..7)

Define the gamma level.

Cameras Camera [1] Mirror

With Mirror mode (horizontal flip) you can mirror the image on screen. Mirroring applies 

both to the self-view and the video that is transmitted to the far end

Requires user role: USER
Default value: Off

Value space: Off/On

Off: Display the image as other people see you.
On: Display the image as you see yourself in a mirror.

Cameras Camera [1] Whitebalance Mode

Define the camera white balance mode.

Requires user role: USER
Default value: Auto

Value space: Auto/Manual

Auto: The camera will continuously adjust the white balance depending on the camera 

view.
Manual: Enables manual control of the camera white balance. The white balance level is 

set using the Cameras Camera [n] Whitebalance Level setting.

Cameras Camera [1] Whitebalance Level

Define the white balance level. Requires the Cameras Camera [n] Whitebalance Mode to be 

set to manual.

Requires user role: USER
Default value: 1

Value space: Integer (1..16)

The white balance level.

Cameras PowerLine Frequency

 The video system's camera is able to compensate for any flicker noise from the electrical 

power supply (power line frequency anti-flickering). The camera also supports auto 

detection of line frequency. Select the Auto option (default), or set this camera configuration 

based on your power line frequency.

Requires user role: ADMIN
Default value: Auto

Value space: 50Hz/60Hz/Auto

50Hz: Use this value when the power line frequency is 50 Hz.
60Hz: Use this value when the power line frequency is 60 Hz.
Auto: Allow the camera to detect the power frequency automatically.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices

System settings

Содержание MX200 G2














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды