Cisco MX200 G2 Скачать руководство пользователя страница 135

Страница: 135 / 141

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.

135

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Remove the back

cover to get access to

the connectors.

Micro USB connector

Computer

Video

system

USB

Micro USB

USB to micro USB cable

Serial interface (RS-232)

Use the micro USB connector for serial communication with

MX200 G2 and MX300 G2. You need a micro USB to USB cable,

and you may need to install a serial port driver on the computer.

The serial connection can be used without an IP-address, DNS, or

a network.

Parameters:

•  Baud rate: 115200 bps
•  Data bits: 8
•  Parity: None
•  Stop bit: 1

Video system settings

Serial communication is enabled by default. Use the following

configuration to change the behavior:

SerialPort > Mode

For security reasons, you are asked to sign in before using the

serial interface. Use the following setting to change the behavior:

SerialPort > LoginRequired

Restart the video system when you have made changes to the

serial port settings.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices



Appendices

Содержание MX200 G2














































































































































Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды

Cisco MX200 G2, Руководство администратора

Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды