Cisco MX200 G2 Скачать руководство пользователя страница 41

Страница: 41 / 141

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

In order to use Touch 10 as user interface for

MX200 G2 and MX300 G2, Touch 10 must either be

directly connected to the video system as described on

this page, or paired to the video system via the network

(LAN) as described on the next page. The latter is

referred to as remote pairing.

Connect Touch 10 directly to the video

system

Connect Touch 10 to the video system as illustrated.

Touch 10 set-up

Once Touch 10 is connected to power, the set-up

procedure begins. Follow the instructions on screen.

If Touch 10 needs software upgrade, new software will

be downloaded from the video system and installed on

the unit automatically as part of the set-up procedure.

Touch 10 restarts after the upgrade.

Connect the Touch 10 controller

(page 1 of 3)

The Ethernet connector

is behind the lid at the

rear of Touch 10.

Contact information

The video system’s

name or address is

displayed in the top

banner when Touch

10 is successfully

connected to the video

system.

PoE rated Ethernet cable

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices



Peripherals

Содержание MX200 G2














































































































































Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды

Cisco MX200 G2, Руководство администратора

Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды