manualshive.com logo in svg

Cisco MX200 G2, Руководство администратора

Поделиться
Скачать
Cisco MX200 G2 Скачать руководство пользователя страница 66

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.  

www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 

66

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Cameras settings

Cameras Camera [1] Backlight DefaultMode

This configuration turns backlight compensation on or off. Backlight compensation is 

useful when there is much light behind the persons in the room. Without compensation the 

persons will easily appear very dark to the far end.

Requires user role: USER
Default value: Off

Value space: Off/On

Off: Turn off the camera backlight compensation.
On: Turn on the camera backlight compensation.

Cameras Camera [1] Brightness Mode

Define the camera brightness mode.

Requires user role: USER
Default value: Auto

Value space: Auto/Manual

Auto: The camera brightness is automatically set by the system.
Manual: Enable manual control of the camera brightness. The brightness level is set 

using the Cameras Camera [n] Brightness DefaultLevel setting.

Cameras Camera [1] Brightness DefaultLevel

Define the brightness level. Requires the Cameras Camera [n] Brightness Mode to be set to 

Manual.

Requires user role: USER
Default value: 20

Value space: Integer (1..31)

The brightness level.

Cameras Camera [1] Focus Mode

Define the camera focus mode.

Requires user role: USER
Default value: Auto

Value space: Auto/Manual

Auto: The camera will auto focus once a call is connected, as well as after moving the 

camera (pan, tilt, zoom). The system will use auto focus only for a few seconds to set the 

right focus; then auto focus is turned off to prevent continuous focus adjustments of the 

camera.
Manual: Turn the autofocus off and adjust the camera focus manually.

Cameras Camera [1] Gamma Mode

This setting enables gamma corrections. Gamma describes the nonlinear relationship 

between image pixels and monitor brightness.

Requires user role: USER
Default value: Auto

Value space: Auto/Manual

Auto: Auto is the default and the recommended setting.
Manual: In manual mode the gamma value is changed with the gamma level setting, ref. 

Cameras Camera [n] Gamma Level.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices

System settings

Содержание MX200 G2














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды