Carrier Access Network Device Axxius 800 Скачать руководство пользователя | Manualshive

Страница: 89 / 568

background image

Axxius 800 - Release 2.2

4-17

Configuration

Setup of DS0 Management Channel

Set IP Configuration of PC

1. Set IP Address to 192.168.201.102

2. Set Gateway to 192.168.201.101 (Router LAN Address)

Configuring the Axxius Router

NOTE:

The Remote Axxius WAN address MUST have a different subnet

than the Axxius Controller Ethernet address.

WAN Connections

The following WAN connections are made from a default condition with one (1)
TSR card installed set with factory defaults.

NOTE:

An Axxius TSR is capable of managing 24 virtual WAN

connections through one of the ports of the Controller card. If support of
more than 24 Axxius units is required a Quad T1 and TSR card(s) can be
added; this however, can only be done on the collocated TSR, not on a
remote Axxius.

1. From the CLI execute the following command to connect one DS0 to each one

of the 24 WANs.

Command

Description

set local off

Sets the Axxius to be configured through CLI

set a:1 down

Sets port 1 of the Controller as Out-of-Service

disconnect a

Disconnects all connections to slot a (controller)

set a:1:1-24 type data

Sets all DS0s on the DS1-1 to data signaling type

connect a:1:1 1:1:1

Connects first DS0 of port 1 of the Controller to
port 1, WAN 1 of the Router in slot 1.

connect a:1:2 1:1:2

Connects second DS0 of port 1 of the Controller to port
1, WAN 2 of the Router in slot 1.

connect a:1:3 1:1:3

Up to 24 WAN connections (a:1:24 1:1:24)

«
...
87
88
89
90
91
...
»

Содержание Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Device Axxius 800

Бренд: D-Linke Страницы: 32

Бренд: 4RF Страницы: 7

Бренд: Paradyne Страницы: 2

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: TRENDnet Страницы: 2

RS-232/422/485 Serial Card CE 3PXCC4A

Бренд: B&B Electronics Страницы: 47

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: Keysight Technologies Страницы: 106

Бренд: EXAGATE Страницы: 7

Бренд: ALIBI Страницы: 232

Бренд: Xinje Страницы: 76

Бренд: Juniper Страницы: 6

Бренд: Gbord Страницы: 11

Threat Analysis Reporter TAR

Бренд: 8e6 Technologies Страницы: 76

RuggedNet 10G/Si

Бренд: OST Страницы: 8

Бренд: TP-Link Страницы: 182

Бренд: B&B Electronics Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды