Carrier Access Network Device Axxius 800 Скачать руководство пользователя | Manualshive

Страница: 419 / 568

background image

Axxius 800 - Release 2.2

11-5

Single Channel POTS Cards

Built-In Card Handles

Built-In Card Handles

The Single Channel POTS cards are designed with a handle built into the faceplate to
assist in the removal of the card from the chassis. This handle slides out away from the
unit, creating a handle for a more effective grip.

Card Configuration

The Single Channel POTS card can be configured, using CLI commands.

CLI Commands

The following commands are used to configure the POTS cards. For detailed
information on these commands, see Chapter 5, CLI Commands.

l

connect
Creates two-way connections between channels

l

disconnect
Removes a connection created by the connect command

l

set (fxsPS or fxsPSM)
To setup the voice channels parameters (rx gain, signal, tx gain).

l

show (fxsPS or fxsPSM)
Displays the settings (type, signaling, rx gain, tx gain) for the FXS PS cards.

l

status (fxsPS or fxsPSM)
Displays the status (AB bits received, AB bits transmitted, signal, T1
activity, trunk processing) of the specified FXS PS cards.

«
...
417
418
419
420
421
...
»

Содержание Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Device Axxius 800

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

Бренд: Danfoss Страницы: 61

Бренд: Profile Страницы: 6

Бренд: Edge-Core Страницы: 7

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

AT-9424Ts/XP AC

Бренд: Allied Telesis Страницы: 3

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

MasterBus Tanklevel Interface

Бренд: Mastervolt Страницы: 8

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

Бренд: Maipu Страницы: 26

Бренд: PRIZM Страницы: 8

Бренд: Netopia Страницы: 138

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренд: IBM Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды