Carrier Access Network Device Axxius 800 Скачать руководство пользователя | Manualshive

Страница: 86 / 568

background image

4-14

Axxius 800 - Release 2.2

Configuration

Setup of DS0 Management Channel

Setup of DS0 Management Channel

The DS0 Management Channel provides an alternative to the FDL link for
management information where FDL is unavailable. The Access Navigator and the
remote Axxius 800 will use IP packets to communicate management and control
information over the DS0 Management channel. A DS0 Channel will be used in the
remote Axxius 800 to send and receive the management IP packets.

The Navigator sends and receives the IP packets over its Ethernet connection while the
remote Axxius sends and receives the IP packets over a DS0 channel. A channelized
router takes the IP messages from the Ethernet to send them over DS0 channels (WAN)
and vice versa. The DS0s coming out of the router are on a single T1. It connects to the
Navigator, where the DS0s are cross-connected to the remote Axxius.

The following procedure will walk you through the basic setup of a DS0 Management
Channel.

Axxius

with Router

192.168.201.101

Axxius

(Axxius1)

192.168.202.1

Axxius

(Axxius2)

192.168.202.2

Access

Navigator

192.168.201.100

One Management

T1 DS0 for each

Remote Axxius 800

IP packets carry Remote

Mgmt messages

PC

192.168.201.102

T1 DS0 carrying

IP Packets

EOD messages

carry ISDN

Voice

Switch

«
...
84
85
86
87
88
...
»

Содержание Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Device Axxius 800

Бренд: Patton electronics Страницы: 8

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: Watchguard Страницы: 24

Бренд: Draytek Страницы: 8

Бренд: SurfControl Страницы: 2

Бренд: ActionTec Страницы: 115

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

NetVanta Serial Dial Backup Interface Module (DIM) none

Бренд: ADTRAN Страницы: 2

Бренд: e+p Страницы: 2

Бренд: N-Tron Страницы: 2

3C13755-US - Router 5642

Бренд: 3Com Страницы: 104

Бренд: Niveo Professional Страницы: 49

Бренд: Paradyne Страницы: 1

Бренд: Umniah Страницы: 12

Бренд: B&B Electronics Страницы: 19

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды