CAMSO 24D18C Скачать руководство пользователя страница 47

Страница: 47 / 106

4 - 24D18C Drive Wheel Seal And Bearing Replacement

STEP 21

Use the same tools and procedures as in Step 19
without a press to completely seat the seal (1) in the
seal shoulder. The seal is completely seated when
the gap between the seal (1) and the spacer (2)
installed in Step 20 is 0.35 mm (0.014 in).

STEP 22

Heat the bearing cone (1) in an oven to 300°F
(148°C) for 20 minutes. Carefully install the inner
bearing cone (1) on the spindle.

WARNING:

Use protective gloves when handling the

bearing cone (1).

STEP 23

Coat the bearing cup mounting surface of the spindle
housing with Loctite® 609 Retaining Compound.

Use a bearing driver to install the outer bearing cup
(1) in the drive spindle housing.

NOTE:

Be sure the bearing cup (1) is completely

seated in the spindle housing.

NOTE:

The bearing cup (1) can be cooled to 0°F (-

18°C) or colder for easier installation.

cp1741

cp1716

cp1715

cp0525

Содержание 24D18C











































































































Результаты поиска

Содержание 24D18C

Отзывы:

CAMSO 24D18C, Руководство по обслуживанию, Страница: 47 / 106

Результаты поиска

Содержание 24D18C

Отзывы: