CAMSO 24D18C Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 106

CAMSO 24D18C Скачать руководство пользователя страница 37

3 - Midroller Wheel Seal And Bearing Removal And Installation

35

STEP 22

Carefully install the hub (1) assembly on the axle
without dislodging the inner bearing and face seal
until the face seals make contact. Hold the hub
assembly in the position for Steps 23 through 25.

NOTE:

On models before TRE0216003 the bearing

is a press fit and will require the hub and bearing
assembly to be pressed on the axle if not heated in
Step 17.

STEP 23

Install the outer bearing cone (1).

IMPORTANT:

The hub MUST be held in place with

slight pressure against the face seals until the lock
nut is installed in Step 25.

STEP 24

Install the locking washer (1).

STEP 25

Use the Locknut Socket (2P-0085) to install the lock
nut (1) and tighten to 150 N•m (112 ft-lb) to fully seat
the bearings. Loosen the locknut 1/2 turn and tighten
to 38 N•m (28 ft-lbs). Rotate the hub five times and
check nut for correct torque.

cp0498

1

cp0497

1

cp0496

1

1

cp0495

1

«
...
35
36
37
38
39
...
»

Содержание 24D18C











































































































Отзывы:

Нет отзывов