manualshive.com logo in svg

Calix ODC-120, Руководство по установке, Страница: 43 / 44

Поделиться
Скачать
Calix ODC-120 Скачать руководство пользователя страница 43

37

Calix ODC-120 Installation Guide

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

© 2005 Calix. All Rights Reserved. 

Step 10:

Slide the Hx assembly back into the Hx assembly as shown in Fig. 38 and replace 
the four mounting bolts for the fan access cover.

CAUTION

Tighten all bolts to 25 in-lb (230-288 Newton-cm).

Step 11:

Connect the power plugs and place it behind the duct.

Step 12:

When all work is complete, apply power to the fans and verify fan operation and 
that there are no fan failures.

10.3 Accessories and Replacement Parts

10.3.4 Contact Emerson Network Power customer service at 800-800-1280 for information regarding 

replacement parts and/or accessories.

TABLE B - Accessory Ordering Guide

Finish Part No. Description

F1005429

MESA

®

 6 NxT / Calix ODC-120 Cabinet

F1005840

Battery Heater Pad Kit for
MESA

®

 6 NxT / Calix ODC-120

* Place on same PO as cabinet for 
factory installation

F1004239

Pad Mounting Template for
MESA

®

 6 NxT / Calix ODC-120

F1006568

Replacement Battery Heater Pad

Содержание ODC-120













































Отзывы:

Нет отзывов