Cabletron Systems ELS10-26 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 170

background image

TCP/IP MIB-II

2-7

ifOutOctets

{ifEntry 16}

Counter Read-Only

The total number of bytes transmitted out the port, counting the
MAC header and FCS.

ifOutUcastPkts

{ifEntry 17}

Counter Read-Only

The number of non-multicast packets transmitted out the port,
regardless of whether or not hardware transmission errors were
encountered.

ifOutNUcastPkts

{ifEntry 18}

Counter Read-Only

The number of multicast packets transmitted out the port,
regardless of whether or not hardware transmission errors were
encountered.

ifOutDiscards

{ifEntry 19}

Counter Read-Only

The number of packets to be transmitted out the port, but were not
transmitted due to non-error reasons. The definition of non-error
reasons is implementation dependent. The ELS10-26 defines
non-error reasons as packet congestion. Packet congestion occurs
when too many packets are to be queued for transmission, or when
packets have been awaiting transmission for too long a time
period.

ifOutErrors

{ifEntry 20}

Counter Read-Only

The number of packets that were to be transmitted out the port,
but incurred transmission hardware errors.

«
...
31
32
33
34
35
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

Бренд: ZALMAN Страницы: 20

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

Бренд: Commell Страницы: 58

Бренд: Alesis Страницы: 46

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

AirStation WHR-G300N

Бренд: Hornington Страницы: 6

Бренд: Patton electronics Страницы: 12

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: Altera Страницы: 42

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды