Cabletron Systems ELS10-26 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 170

background image

1-1

CHAPTER 1

INTRODUCTION

This manual is for system administrators responsible for
configuring, monitoring, and maintaining the ELS10-26. Much of
the configuration of the ELS10-26 needs to be done using an
SNMP-based network management station. This manual contains
the SNMP MIB variables you may need to configure, monitor, and
manage your ELS10-26. You should use this manual with the

ELS10-26 User Guide

and with the documentation provided with

your NMS.

The contents of each chapter are described below.

• Chapter 1,

Introduction

, provides an overview of the SNMP

primitives, describes the functions the MIB variables can be used
to perform, and describes how to use TFTP to download the
ELS10-26 system software.

• Chapter 2,

TCP/IP MIB-II

, describes the standard TCP/IP MIB

variables.

• Chapter 3,

Ethernet MIB

, describes the standard Ethernet MIB

variables.

• Chapter 4,

Bridge MIB

, describes the Bridge MIB variables.

• Chapter 5,

PPP MIB

, describes the PPP link control and IP table

MIB variables.

• Chapter 6,

ELS10-26 MIB

, describes the Cabletron enterprise

MIB variables.

• Chapter 7,

Traps

, describes generic and enterprise-specific

traps.

«
...
9
10
11
12
13
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Бренд: Wave wifi Страницы: 2

Бренд: LAWO Страницы: 154

SR8800 IM-FW-II

Бренд: H3C Страницы: 107

Бренд: 3Com Страницы: 12

Бренд: H3C Страницы: 16

H3C S3600 Series

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 2

H3C S7500E Series

Бренд: H3C Страницы: 34

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 14

Бренд: H3C Страницы: 56

H3C S7500E Series

Бренд: H3C Страницы: 112

Бренд: H3C Страницы: 15

SR8800 IM-FW-II

Бренд: H3C Страницы: 5

H3C S7500E Series

Бренд: H3C Страницы: 50

Бренд: H3C Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды