Cabletron Systems ELS10-26 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 170

background image

2-12

TCP/IP MIB-II

ipReasmOKs

{ip 15}

Counter Read-Only

The number of IP datagrams which were successfully reassembled.

ipReasmFails

{ip 16}

Counter Read-Only

The number of failures (for whatever reason timed-out, errors, etc.)
detected by the IP reassembly algorithm. This is not necessarily a
count of discarded IP fragments since some algorithms (notably
RFC 815) can lose track of the number of fragments by combining
them as they are received.

ipFragOKs

{ip 17}

Counter Read-Only

The number of IP datagrams that have been successfully
fragmented within this ELS10-26.

ipFragFails

{ip 18}

Counter Read-Only

The number of IP datagrams that have been discarded because
they needed to be fragmented but could not be (e.g., because their
“Don’t Fragment” flag was set).

ipFragCreates

{ip 19}

Counter Read-Only

The number of IP datagram fragments that have been generated
by this ELS10-26.

2.4.1 IP Address Table

The TCP/IP IP Address Table contains the IP addressing
information for each port. The parameters are described below.

«
...
36
37
38
39
40
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

Бренд: Hal Communications Страницы: 25

Бренд: Yamaha Страницы: 4

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

Бренд: FONESTAR Страницы: 8

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: iCEBOX Страницы: 57

Бренд: East Coast Datacom Страницы: 19

Бренд: ProCurve Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды