Cabletron Systems ELS10-26 Скачать руководство пользователя страница 166

Страница: 166 / 170

7-6

Traps

lxStorageFailureTrap (17) - Sent if the unit’s Configuration
EEPROM has failed.

Cabletron MIB variables include:

• lxTrapSeverity

lxPortCongestionTrap (18) - Sent whenever outbound congestion
control has been invoked for the port.

Cabletron MIB variables include:

• lxTrapSeverity

• ifOutDiscards

lxTopChangeBegunTrap (19) - The spanning tree topology has
begun to change.

Cabletron MIB variables include:

• lxTrapSeverity

lxTopChangeEndTrap (20) - The spanning tree topology has
stopped changing.

Cabletron MIB variables include:

• lxTrapSeverity

lxIfErrorsTrap (21) - Sent whenever the number of hardware errors
in received and transmitted packets has exceeded the port’s limit.

Cabletron MIB variables include:

• lxTrapSeverity

• ifInErrors

• ifOutErrors

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды