Cabletron Systems ELS10-26 Скачать руководство пользователя страница 84

Страница: 84 / 170

3-4

Ethernet MIB

dot3StatsSQETestErrors

{dot3StatsEntry 6}

Counter Read-Only

The number of times an SQE failure (i.e., heartbeat lost) occurred,
since the port was last enabled.

dot3StatsDeferredTransmissions

{dot3StatsEntry 7}

Counter Read-Only

The number of frames for which the first transmission attempt was
successful, but delayed because the medium was busy.

dot3StatsLateCollisions

{dot3StatsEntry 8}

Counter Read-Only

The number of times that a late collision was detected while the
ELS10-26 was transmitting a frame.

dot3StatsExcessiveCollisions

{dot3StatsEntry 9}

Counter Read-Only

The number of times a frame transmission attempt experienced
excessive collisions, since the port was last enabled.

dot3StatsInternalMACTransmitErrors

{dot3StatsEntry 10}

Counter Read-Only

The number of times a frame transmission attempt experienced an
error other than dot3StatsSQETestErrors,
dot3StatsExcessiveCollisions, or dot3StatsCarrierSenseErrors,
since the port was last enabled.

dot3StatsCarrierSenseErrors

{dot3StatsEntry 11}

Counter Read-Only

The number of times that a carrier sense condition was lost during
a transmission attempt, since the port was last enabled.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды