Cabletron Systems ELS10-26 Скачать руководство пользователя страница 49

Страница: 49 / 170

TCP/IP MIB-II

2-23

udpInDatagrams

{udp 1}

Counter Read-Only

The total number of UDP datagrams delivered to UDP users.

udpNoPorts

{udp 2}

Counter Read-Only

The total number of received UDP datagrams for which there was
no application at the destination port.

udpInErrors

{udp 3}

Counter Read-Only

The number of received UDP datagrams that could not be
delivered for reasons other than the lack of an application at the
destination port.

udpOutDatagrams

{udp 4}

Counter Read-Only

The total number of UDP datagrams sent from this ELS10-26.

2.7.1 UDP Listener Table

The TCP/IP UDP Listener Table parameters are described below.

udpTable

{udp 5}

Not Accessible

A table containing UDP listener information. The table has entries
for the following UDP port numbers port 69 (default TFTP port
number), port 161 (SNMP port number), and port 520 (RIP port
number).

udpEntry

{udpTable 1}

Not Accessible

The entry information of the IP address and UDP port
combination.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды