Cabletron Systems ELS10-26 Скачать руководство пользователя страница 138

Страница: 138 / 170

6-26

ELS10-26 MIB

lxprotoTrunking

{lxsprotoEntry 5}

Integer Read-Write

Specifies whether Cabletron’s trunking protocol (an extension to
the standard Spanning Tree) is to be used over this port. Values
include:

• enabled (1)

• disabled (2)

lxprotoTransmitPacing

{lxprotoEntry 6}

Integer Read-Write

When enabled, introduces delays into normal transmission of
frames to reduce the probability of collisions during heavy traffic.

• enabled (1)

• disabled (2)

6.1.10 Cabletron Trunking Group

lxtrunkTable

{lxtrunk 1}

Not Accessible

This table describes the trunking status and attributes of the
interfaces that are configured for bridge trunking.

lxtrunkEntry

{lxtrunkTable 1}

Not Accessible

An entry exists for every port that has trunking enabled.

lxtrunkIfIndex

{lxtrunkEntry 1}

Integer Read-Only

Identifies the port that is configured for trunking.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды