Cabletron Systems ELS10-26 Скачать руководство пользователя страница 154

Страница: 154 / 170

6-42

ELS10-26 MIB

6.1.15 Traceroute Management MIB

lxtraceDataTimout OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The time, in centiseconds, from
the last traceroute activity, (the
response to, or timeout of the last
probe sent) to when the lxtra-
ceEntry information for that trac-
eroute request will be deleted.

::= {lxtraceMgt 1}

lxtraceTable OBJECT-TYPE

SYNTAX

SEQUENCE OF lxtraceEntry

ACCESS

not accessible

STATUS

mandatory

DESCRIPTION

The set of information describing
the active traceroute request.

::= {lxtraceMgt 2}

lxtraceEntry OBJECT-TYPE

SYNTAX

lxtraceEntry

ACCESS

not accessible

STATUS

mandatory

DESCRIPTION

The parameters, state, and
results of a traceroute request.

INDEX

{lxtraceNMSAddr, lxtraceDes-
tAddr, lxtraceHop, lxtraceProbe}

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды