Cabletron Systems ELS10-26 Скачать руководство пользователя страница 151

Страница: 151 / 170

ELS10-26 MIB

6-39

STATUS

mandatory

DESCRIPTION

The time, in centiseconds, since
the last ECHO-RESPONSE was
received (or the last
ECHO-RESPONSE was sent, if
there have been no responses)
when the ping request will time
out. This variable cannot be set
while the lxpingOperation is on.

::= {lxpingEntry 7}

lxpingOperation OBJECT-TYPE

SYNTAX

INTEGER {on (1), off (2) }

ACCESS read-write

STATUS

mandatory

DESCRIPTION

Setting lxpingOperation to on
will begin the ping request. Set-
ting lxpingOperation to off will
terminate the ping request.

::= {lxpingEntry 8}

lxpingMin OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The minimum round trip time
for the ping requests and
responses, in centiseconds.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды