Cabletron Systems ELS10-26 Скачать руководство пользователя страница 136

Страница: 136 / 170

6-24

ELS10-26 MIB

• 38400-baud (7)

• 56-kilobits (8)

• 1.544-megabits (9)

• 2.048-megabits (10)

• 45-megabits (11)

lxsuartAlignmentErrors

{lxuartEntry 3}

Counter Read-Only

Number of received packets with frame alignment errors, since the
port was last enabled.

lxsuartOverrunErrors

{lxuartEntry 4}

Counter Read-Only

Number of received packets with data overrun errors, since the
port was last enabled.

6.1.9 Cabletron Protocol Group

This group specifies which protocols apply to each interface.

lxprotoTable

{lxsproto 1}

Not Accessible

This table contains configuration information specifying the types
of protocols used for each port.

lxprotoEntry

{lxsprotoTable 1}

Not Accessible

Each entry in this table specifies which protocols are used by a
particular port in the ELS10-26.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды