Cabletron Systems ELS10-26 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 170

background image

1-2

Introduction

1.1 RELATED DOCUMENTATION

You may need to refer to the following Cabletron documentation:

•

ELS10-26 User Guide

– contains installation, configuration, and

management instructions for the ELS10-26. It also describes how
to use the Local Console Manager (LCM), which is a
non-intelligent terminal interface to the ELS10-26.

If you need internetworking reference material, you may find the
following books helpful:

•

Interconnections, Bridges and Routers,

Radia Perlman, Addison

Wesley © 1992.

•

Internetworking with TCP/IP: Principles, Protocols, and Architecture

(2nd edition), Volumes I and II, Douglas Comer,
Prentice Hall © 1991.

•

The Simple Book, An Introduction to Management of TCP/IP-based
internets

(2nd edition), Marshall T. Rose, Prentice Hall © 1994.

This manual describes the software interface between the NMS
and the ELS10-26. This is relevant for an ELS10-26 running Version
1.0 software. The NMS communicates with the ELS10-26 software.

The Network Management, or UART, port is the interface to the
Local Console Manager (LCM). LCM is a non-intelligent terminal
interface that can be used to configure and monitor status for the
ELS10-26.

«
...
10
11
12
13
14
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 4

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

SmartSTACK ELS100-24TXG

Бренд: Cabletron Systems Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды