Cabletron Systems ELS10-26 Скачать руководство пользователя страница 61

Страница: 61 / 170

TCP/IP MIB-II

2-35

2.14 CABLETRON COM PORT CONFIGURATION GROUP

ctCpTable

{ctIfCp 1}

This table defines a Com Port Table.

SYNTAX SEQUENCE OF ctCPEntry

ACCESS not accessible

STATUS mandatory

OBJECT IDENTIFIER: 1.3.6.1.4.1.52.4.3.3.4.1

ctCpEntry

{ctCpTable 1}

This defines each conceptual row within the ctCpTable.

SYNTAX ctCpEntry

ACCESS not accessible

STATUS mandatory

OBJECT IDENTIFIER: 1.3.6.1.4.1.52.4.3.3.4.1.1

INDEX

ctComPort

{ctCpEntry 1}

This is the index into the Com Port Table and defines the Com Port
that is being described. com1 = 1, com2 = 2.

SYNTAX INTEGER

ACCESS read-only

STATUS mandatory

OBJECT IDENTIFIER: 1.3.6.1.4.1.52.4.3.3.4.1.1.1

We only have one UART port. This means the OID will always be
OBJECT IDENTIFIER: 1.3.6.1.4.1.52.4.3.3.4.1.1.1.1, and we will
always return a value of 1.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды