Cabletron Systems ELS10-26 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 170

background image

2-2

TCP/IP MIB-II

the Cabletron MIB sysID object, i.e., {1 3 6 1 4 1 97 5 7}. Special
versions of the ELS10-26, made for third-party vendors may use
different values for sysID.

sysUpTime

{system 3}

TimeTicks Read-Only

The time, in centiseconds, since the ELS10-26 was last booted.

sysContact

{system 4}

DisplayString Read-Write

The name and address of the contact person for the ELS10-26.

sysName

{system 5}

DisplayString Read-Write

The Internet name of the contact person for the ELS10-26. The
LCM prompt consists of sysName followed by “>”. (LCM is a
non-intelligent terminal interface that can be used to configure and
monitor status for the ELS10-26.)

sysLocation

{system 6}

DisplayString Read-Write

The physical location of the ELS10-26.

sysServices

{system 7}

Integer Read-Only

The sum of the services supported by the ELS10-26. Values
include:

(2)

the ELS10-26 is a bridge only

2.2 INTERFACES GROUP

interfaces

{mib-2 2}

The TCP/IP Interfaces Group parameters are described below.

«
...
26
27
28
29
30
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

Бренд: Linksys Страницы: 2

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

MMAC-Plus 9F106-02

Бренд: Cabletron Systems Страницы: 7

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: IBM Страницы: 32

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Бренд: D-Link Страницы: 53

Бренд: Vonets Страницы: 8

Бренд: D-Link Страницы: 83

Бренд: Lanner Страницы: 63

Momentum ROG Strix X570-E D-RGB

Бренд: EK-Quantum Страницы: 10

Бренд: Renesas Страницы: 941

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды