Cabletron Systems ELS10-26 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 170

background image

ELS10-26 MIB

6-25

lxprotoIfIndex

{lxsprotoEntry 1}

Integer Read-Only

Identifies the interface (port) to which this entry’s information
belongs. The value of this variable corresponds to lxifIndex, as well
as to most of the other port identification values in related MIBs.

lxprotoBridge

{lxsprotoEntry 2}

Integer Read-Write

Defines the bridging method to be applied to frames received at, or
destined for this port. Ethernet and FDDI ports may be configured
for transparent, srt, or none. Token Ring ports may be configured
for any of the four options. The UART may only be configured to
none.

lxprotoSuppressBpdu

{lxsprotoEntry 3}

Integer Read-Write

Allows transmission of spanning tree protocol packets to be
suppressed. Values include:

• normal (1) – 802.1d Spanning Tree protocol packets are

transmitted as usual

• suppressed (2) – these packets are not transmitted. This option

may be useful for interoperability with non-802.1d spanning
tree protocols.

lxprotoRipListen

{lxsprotoEntry 4}

Integer Read-Write

Specifies whether the port should listen for internet RIP packets so
the ELS10-26 can build a routing table for the unit. Values include:

• enabled (1)

• disabled (2)

«
...
135
136
137
138
139
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

Бренд: D-Link Страницы: 29

DGS-3700 Series

Бренд: D-Link Страницы: 292

Бренд: D-Link Страницы: 140

DGS-1224T - Web Smart Switch

Бренд: D-Link Страницы: 61

DI-LB604 - Load Balancing Router

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 45

Бренд: D-Link Страницы: 218

DES-3528 - xStack Switch - Stackable

Бренд: D-Link Страницы: 322

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 10

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 4

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 13

DI-804HV - Express ENwork Router

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды