Cabletron Systems ELS10-26 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 170

background image

7-2

Traps

authenticationFailure (4) - This trap is generated whenever the
community name in a PDU does not match the corresponding
password. All SetRequest PDUs must match the configAnyPass
(refer to the of lxadminGetPass for SetRequest exceptions),
GetRequest PDUs must match either the lxadminGetPass or the
configAnyPass. The GetRequest exception is for one of the
debugging attributes; those PDUs must always provide the
lxadminAnyPass.

egpNeighborLoss (5) - Not used by the ELS10-26.

7.2 ENTERPRISE SPECIFIC TRAPS FOR THE ELS10-26

This section lists the enterprise-specific traps that can be generated
by the ELS10-26. ELS10-26 traps contain enterprise-specific
variables that are defined in the system group of the Cabletron
MIB in Chapter 6 of this manual.

lxWriteStatusTrap (2) - Sent when a bank of Flash EPROM has been
erased. If lxswdisWriteStatus indicates success, then the unit is
ready to be downloaded with the new software.

Cabletron MIB variables include:

• lxTrapSeverity

• lxswdisWriteStatus

• lxwdisDesc

lxPortFunctionsTrap (3) - Sent whenever the current functional
state (active protocols) of the port has changed.

Cabletron MIB variables include:

• lxTrapSeverity

• lxifFunction

«
...
160
161
162
163
164
...
»

Содержание ELS10-26











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ELS10-26

Бренд: Xantrex Страницы: 8

Бренд: Campbell Страницы: 42

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: Quatech Страницы: 27

Бренд: Rane Страницы: 4

Бренд: SyChip Страницы: 24

Бренд: RAIDAGE Страницы: 60

Teranex 2D Processor

Бренд: Blackmagicdesign Страницы: 969

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: IEI Technology Страницы: 2

Бренд: Xantech Страницы: 5

Accelero TWIN TURBO II

Бренд: Arctic Страницы: 2

Бренд: OPTO 22 Страницы: 28

Бренд: ETAS Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды