Cabletron Systems ELS10-26 Скачать руководство пользователя страница 114

Страница: 114 / 170

6-2

ELS10-26 MIB

sysTrapPort

{sys 6}

Integer Read-Write

zero, or the UDP port number to which a second copy of SNMP
traps should be sent. Valid values are 0 through 65535.

6.1.1 Hardware Configuration Group

lxhwDiagCode

{lxhw 1}

Octet String Read-Only

This variable is for Cabletron internal use only.

lxhwManufData

{lxhw 2}

DisplayString Read-Only

This is a 64-byte array which contains the part number, serial
number, and hardware revision level of this unit.

lxhwPortCount

{lxhw 3}

Integer Read-Only

The number of ports, including the out-of-band management port.

lxhwPortTable

{lxhw 4}

Not Accessible

A table that includes information for each port.

lxhwPortEntry

{lxhwPortTable 1}

Not Accessible

An entry for an individual port, keyed by lxhwPortIndex.

lxhwPortIndex

{lxhwPortEntry 1}

Integer Read-Only

The port number. The value is from 1 to 25.

Содержание ELS10-26











































































































































































Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды

Cabletron Systems ELS10-26, Справочное руководство

Результаты поиска

Содержание ELS10-26

Отзывы:

Похожие инструкции для ELS10-26

Бренды по названию

Популярные бренды