Buderus Logamax plus GB142-24 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 100

background image

Please read thoroughly before installing and servicing

7212 9700 – 12/2004 US/CA(EN)

For registered installers

Installation and Servicing instructions

Condensing gas heater
Logamax plus GB142-24/30/45/60

CAUTION!

Before putting the appliance into operation read this manual carefully.

WARNING!

Improper installation, adjustment, alteration, service or maintenance
can cause injury, loss of life or property damage. Refer to this manual.
For assistance or additional information consult a qualified installer,
service agency or the gas supplier.

CAUTION!

The operating manual is part of the documentation that is delivered to
the installation's operator. Go through the information in this manual
with the owner/operator and make sure that he or she is familiar with
all the necessary operating instructions.

Notice:

This manual must be retained for future reference.

–

Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.

– What to do if you smell gas

•

Do not try to light any appliance

•

Do not touch any electrical switch; do not use any phone in
your building.

•

Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

Warning: If the information in these instructions is
not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.

1
2
3
...
»

Содержание Logamax plus GB142-24





































































































Отзывы:

Нет отзывов

Похожие инструкции для Logamax plus GB142-24

Wessex Modumax 100 series

Бренд: Hamworthy Страницы: 60

Бренд: Rima Heating Systems Страницы: 27

Бренд: VOKERA Страницы: 48

Бренд: Ideal Boilers Страницы: 8

Бренд: Saturn Страницы: 17

Immergas Zeus Mini

Бренд: RVR Energy Technology Страницы: 17

ECO COMPACT 200

Бренд: Pleion Страницы: 11

Бренд: Navien Страницы: 29

Бренд: CleaverBrooks Страницы: 70

Бренд: CleaverBrooks Страницы: 124

Бренд: Chaffoteaux & Maury Страницы: 12

Brava One HE 25 ErP

Бренд: Sime Страницы: 68

HE COMBI EXTERNAL

Бренд: Immergas Страницы: 32

Бренд: Immergas Страницы: 40

Бренд: HTP Страницы: 75

Бренд: HTP Страницы: 80

Бренд: HTP Страницы: 89

Бренд: Phantom Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды