![background image](http://html.mh-extra.com/html/bticino/d45/d45_technical-manual_2825385053.webp)
51
D
45
VIDEO
DOOR
ENTR
Y SY
STEM
DIP switch setting instruction
Distance
1
2
3
4
colour signal
0 – 300 m
OFF
OFF
OFF
OFF
300 – 700 m
ON
OFF
OFF
OFF
700 – 1000 m
ON
ON
OFF
OFF
b/w signal
1000 –1500 m
ON
ON
ON
OFF
1500 – 2000 m
ON
ON
ON
ON
system conFiguration instructions
Only if the configuration is correct can the device
work correctly . District generator system configuration
includes District generator level mode; dial address of the
Switchboard managed by District generator etc . The District
generator can be configured in three ways . The configurator
alternative has the highest priority . If configurator method
is used, the other method will not work . Note: When the
configurator method is used, after the procedure disconnect
and reconnect the power to activate the configuration .
1 . resistor configuration method .
There is only one configuration method using the
configurator . For the details please see the system
configuration chapter .
2 . Pushbutton method ( only effective when the resistor
configuration method is not used)
EPS EPS MC
min
MC
min
MC
max
MC
mac P/S
1 . Enter configuration status: in standby press input key S2
and hold for 2 s . The CFG light will be always on . Enter
the configuration setup status . (If there is a resistor
configurator installed or if the pushbutton configuration
has been performed incorrectly, the device cannot enter
configuration setup status .
conFiguration inquiry:
1 . Enter configuration enquiry status: in standby press input
key S1 and hold for 2 s . The CFG light will come on and the
device will switch to configuration enquiry status .
2 . Enter the configurator number (i .e . select one
configurator): press S2 to count . Each pressure will
increase the number by one (no press= 1st one) and the
CFG light will flash once .
3 . Confirm the configuration parameter: press S1, the CFG
light will flash quickly a number of times . This number
of times depends on the parameters being read (for
example, if the parameter read is 0, there is no flashing,
for one it will flash once, for two it will flash twice, and
so on for the others (4) . Exit configuration enquiry
status: The CFG light will be off . If no key is pressed for
10 s during the operation the device will automatically
switch to standby . The CFG light will be off .
The video gain setting can be divided into 5 branches,
branch1, branch 2, branch 3, branch 4, wall EP, or release
message to handset channel . They can all be set according
to the instruction data in following table . However, these
data may be different during actual installation . To adjust
and set the data take into account the actual image .
1 2
3 4
on
oFF
2 . Enter the configuration number (select which place): press
S2 to count . Each pressure will increase the number by
one (no press= 1st one) and the CFG light will flash once .
3 . Confirm the configurator number: press S1 then CFG
light flash quickly twice . Then it will come on steady .
4 . Enter the configuration parameter: press S2, the default
parameter is 0 . Increase by 1 with each pressure . The CFG light
will flash quickly twice . The highest number possible is 9 .
5 . Confirm the configuration parameter: press S1, the CFG
light will flash quickly twice and then flash slowly twice .
Then the configuration procedure for this step is now
completed .
6 . Set the next parameters: if necessary, set the other
configuration parameters, press S2 . The CFG light will
flash quickly 3 times . Then proceed according to (2) .
7 . Complete the configuration: press S1 to exit
configuration . The CFG light will be off .
If the operation is successful, the CFG light will flash
slowly once . Restart to activate the new configuration .
If the configuration is not successful (for example, one
configuration exceeds the acceptable value, e .g . P/S>1),
the CFG light will be off, and the old configuration will be
still effective . If the configuration value has logical errors
(for example, EPS>80 or MC Min > MC Max), after restart
the CFG light will keep flashing slowly to indicate the error
and pushbutton operation will be disabled . In this case it
will be necessary to connect a non-zero (1- 9) configurator
to the right position (from the 1st to the 7th position of
the configurator) and reconnect the power to clear the
pushbutton configuration . Then remove the configurators,
reconnect the power and repeat the above configuration
steps . If no pushbutton is pressed for 10s during the
operation, the device will automatically exit configuration
mode and the CFG light will go off .
Содержание D45
