BTG Visual-ICE Скачать руководство пользователя страница 91

Страница: 91 / 126

Visual-ICE™ Cryoablation System

7-9

7.4

Mechanical Issues

Symptom

Potential Causes / Solutions

Needle cannot be firmly connected

in the needle port

1. Verify that the locking bar is in the UNLOCKED position.
2.

Needle connector may be defective. Use a different

needle.

3. Residual gas pressure may be in the needle port. Use a

different channel.

4. Check the

Gas Indicator

display. If there is pressure in

the system, end the procedure and vent the system using

the automatic vent function.

Locking bar on the Needle

Connection Panel cannot be

positioned in the LOCKED position

1. Verify that all needles in the channel are fully inserted in

the needle connection ports.

2. The Locking Bar may be defective. Move the needle to a

different channel. Contact Galil Medical customer service

to schedule a service call.

3. Check the Gas Indicator display and verify the system is

not pressurized. If there is pressure in the system, end

the procedure and vent the system using the automatic

vent function.

Console does not move freely

1. Release the brake to unlock the front wheels.
2. Check the individual rear wheel brakes and ensure the

brakes are released.

7.5 Gas Cylinders and Gas Supply Lines

Symptom

Potential Causes / Solutions

Safety cable is missing at either the

cylinder side or the system side of

the gas supply line

Do not use a gas supply line with a missing safety cable.

Doing so could compromise the safety of personnel in the

room. Contact Galil Medical Customer Service.

A gauge or a gas supply line is

damaged

Do not use any damaged product. Contact Galil Medical

Customer Service for new accessories.

A gas leak was detected between

the gauge adapter and the cylinder

main valve

•

Tighten the connection using the wrench provided with

the Visual-ICE System.

•

Close the cylinder valve and vent the gas from the

Visual-ICE System and the gas supply lines using the

Manual Vent Valve (Figure 4-1). Verify the system is

depressurized. Loosen and remove the gauge assembly

adapter. Verify no debris is on the gas cylinder connection

point; clean the sealing surface as needed to remove

any debris. Reposition and tighten the gauge assembly

adapter onto the cylinder valve, using the wrench

provided with the Visual-ICE System.

Содержание Visual-ICE































































































































Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды

BTG Visual-ICE, Руководство пользователя

Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды