BTG Visual-ICE Скачать руководство пользователя страница 116

Страница: 116 / 126

8-2

User Manual

8.6

Gas Cylinder Specifications

•

Maximum Pressure: 31 MPa (4500 psi, 310 bar)

41.4 MPa (6000 psi, 414 bar)

USA Only

•

Recommended Volume of Gas Cylinders: 42 – 50 L

1.1 Accuracy of Displayed Values

•

Temperature Accuracy:

± 3°C over range of -60°C to +40°C

•

Supplied Gas Pressure Accuracy: ± 50 psi, over range of 1000 psi to 6000 psi

± 3.4 bar over range of 69 bar to 414 bar
± 0.314 MPa over range of 6.9 MPa to 41.4 MPa

•

Built-in Regulator Gas Pressure:

± 50 psi, over range of 1000 psi to 4000 psi

± 3.4 bar over range of 69 bar to 276 bar

± 0.314 MPa over range of 6.9 MPa to 27.6 MPa

•

Time Intervals:

± 5 seconds over any 10 minute interval

8.7

Electrical Specifications

•

Input Voltage: 100 to 240 VAC, single phase

•

Input Frequency: 50 – 60 Hz

•

VA Rating: 250 VA

•

IP Rating: IP10

•

Fuse Rating: T 3.15A

•

Electrical Protection: Class I, Type BF protection against shock

•

Signal Input/Output Ports: one (1) Ethernet port, one (1) USB 2.0 full-speed port, one (1) USB

2.0 low-speed port

8.7.1 Electromagnetic Compatibility and Immunity (EMC and EMI)

The Visual-ICE Cryoablation System needs special precautions regarding electromagnetic

compatibility (EMC) and needs to be installed and placed into service according to the EMC

information provided below.

The Visual-ICE Cryoablation System has been tested in the operating room environment for

electromagnetic compatibility (EMC) and electromagnetic interference (EMI) compliance. The Visual-

ICE Cryoablation System has been tested to be in compliance with IEC 60601-1-2 and EN 55011.

Portable and mobile radiofrequency (RF) communications equipment can affect the Visual-ICE

Cryoablation System, causing it to operate improperly.

Содержание Visual-ICE































































































































Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды

BTG Visual-ICE, Руководство пользователя

Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды