BTG Visual-ICE Скачать руководство пользователя страница 52

Страница: 52 / 126

4-6

User Manual

After successful login, the

Startup Screen

appears (Screen 3-2).

4.1.2 Connecting Gas Cylinders

WARNING. Do not connect the Visual-ICE Cryoablation System to a gas supply exceeding

6000 psi (414 bar, 41.4 MPa) to avoid damage to internal system components.
WARNING. Ensure that the gas cylinders are chained to a wall or an approved cart to prevent

inadvertent tipping of the cylinders.
CAUTION.

Galil Medical recommends having additional backup argon cylinders available for each

treatment.

CAUTION.

Turn the Visual-ICE Cryoablation System ON before connecting the gas cylinders to

ensure the proper diagnostic tests are conducted.

NOTE:

If cryoablation needles with i-Thaw technology are being used, only argon gas is required

to be connected. If helium gas is connected, i-Thaw technology is disabled and only thawing with

helium gas is available.

Position the gas cylinder(s) close enough to the Visual-ICE System to ensure that the gas supply

line is not stretched and does not present a trip hazard.

2. On the rear of the Visual-ICE System, ensure that the Manual Vent Valve is in the CLOSED

position.

Remove the humidity covers from the helium and argon inlets on the Visual-ICE System.

Secure the safety cable at the end of the gas supply line to the system.

WARNING. Ensure that the safety cable is properly secured to the system in case the gas

supply line becomes accidentally disconnected.

Connect the helium high-pressure gas supply line to the helium inlet of the Visual-ICE System

using the quick-connect connector located at the rear of the system.

Figure 4-1. Visual-ICE System Gas Connections

Safety cable

Quick-connect connectors

Humidity cover

Содержание Visual-ICE































































































































Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды

BTG Visual-ICE, Руководство пользователя

Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды