BTG Visual-ICE Скачать руководство пользователя страница 47

Страница: 47 / 126

Visual-ICE™ Cryoablation System

4-1

4 SYSTEM OPERATION

Table 4-1 depicts the order and steps of the Visual-ICE™ Cryoablation System set-up and treatment

procedure. Each step is described in detail in this chapter.

Table 4-1. Cryoablation Procedure Flow

Set-up Console

•

Confirm availability of gas, needles, and accessories

•

Position Visual-ICE System and lock brake

•

Ensure Manual Vent Valve is closed and Argon

Shutoff Valve is ON

•

Power Visual-ICE System ON

•

Connect Gas

Cylinders

•

Connect helium gas, if applicable

•

Connect argon gas

•

Ensure safety cables are connected

•

OPEN valve on helium, then argon

Needle / MTS

Testing

•

Enter patient treatment information in Registration

Button

•

Prepare sterile needles for testing

•

Connect needles to Visual-ICE System and lock

channels

•

Perform Needle Integrity and Functionality Test

•

Test Multi-Point Thermal Sensors, if applicable

Conduct

Cryoablation

Procedure

•

Insert needles into target tissue

•

Deliver the cryoablation treatment and remove

needles

•

View and save reports, if desired

•

Depressurize the system and shutdown

4.1 Preparation for Use

Prior to using the Visual-ICE System, inspect the chassis, power cord, brake, safety cables, gas

supply lines, gas connections, and the monitor touch screen to ensure they are not damaged. If any

of the components are damaged, contact Galil Medical Customer Service.

CAUTION.

If condensation is present on the system, allow the system to dry completely for 12

hours prior to powering up the system. Powering up the system with condensation could result in

permanent damage to the electrical boards, causing the system to be inoperable.

Before the patient is anesthetized

, set up the Visual-ICE System, connect the gas cylinders, and

conduct functionality tests on each cryoablation needle and thermal sensor (reference Section 4.1.4).

Содержание Visual-ICE































































































































Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды

BTG Visual-ICE, Руководство пользователя

Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды