BTG Visual-ICE Скачать руководство пользователя страница 81

Страница: 81 / 126

Visual-ICE™ Cryoablation System

6-1

6 SYSTEM CARE and MAINTENANCE

6.1 System Installation

Installation instructions for the Visual-ICE™ System are included in the shipping carton, available

online at www.galilmedical.com/customerservice, or by contacting your local Galil Medical

representative.

6.2 Cleaning

6.2.1 Cleaning the Visual-ICE System

Clean the Visual-ICE Cryoablation System after each use by following the steps below.

1. Clean the Touch Screen Monitor when the Visual-ICE Cryoablation System is powered OFF.

•

Wipe the screen gently with a damp gauze wipe.

•

Use water or isopropyl alcohol only.

•

Do not use cleaning agents such as Betadine or bleach solution.

2. Clean the Visual-ICE Cryoablation Console by wiping with a damp gauze wipe.

•

Use soap and water or isopropyl alcohol cleaning solutions.

•

Do not use cleaning agents such as Betadine or bleach solution.

•

Do not allow water or other liquid to drip or seep inside the cryoablation needle connection

ports. The needle connection ports must remain completely dry at all times.

3. Ensure that cleaned surfaces are dry prior to closing or turning on the system.

CAUTION.

Do not set food, drinks, or other objects on top of the Visual-ICE Cryoablation System.

Doing so may damage the system.

6.2.2 Cleaning the Stylus

Clean the stylus after each use by wiping down with isopropyl alcohol. Dry the stylus with a dry

gauze wipe.

6.3 Service and Preventive Maintenance

Only trained and authorized service engineers are permitted to conduct service and system

preventive maintenance on the system. Preventive maintenance on the Visual-ICE Cryoablation

System will be performed every two years.

CAUTION.

Do not attempt to service the Visual-ICE Cryoablation System. If service is required,

contact Galil Medical Customer Service.

The Visual-ICE Cryoablation System will display a reminder on the screen approximately one

month prior to when the preventive maintenance is due. If the reminder message appears and the

preventive maintenance has not yet been scheduled, contact your Galil Medical authorized service

representative to schedule the service.

Содержание Visual-ICE































































































































Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды

BTG Visual-ICE, Руководство пользователя

Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды