BTG Visual-ICE Скачать руководство пользователя страница 85

Страница: 85 / 126

Visual-ICE™ Cryoablation System

7-3

7.2

Electronics, Electrical and User Error Related Issues

Symptom

Potential Causes / Solutions

System does not turn ON (i.e., the

fan is not running) or power is lost

during procedure

1. The power control knob on the front panel of the system

or power switch on the rear panel is OFF (Figure 2-1

and Figure 2-2). Turn the power ON.

2. The power cable to the Visual-ICE System is

disconnected from the power outlet or from the rear

panel of the system. Connect the power cable to the

Visual-ICE System, checking that the power cable is fully

seated. Connect the power cable to the power outlet.

3. There is no power at the wall outlet. Ensure the power

outlet is switched ON. Call the hospital Biomedical

Engineer for assistance, if needed.

4. A fuse may have blown. Spare fuses are located in the

power cord inlet on the system (Figure 2-2). Reference

Section 7.2.1 for instructions on how to replace fuses in

the system.

Channel or needle is not

recognized by the system and not

available for use

1. Check the corresponding Channel Locking Bar and

ensure it is fully in the locked position.

2. At least one needle must be inserted into a channel for

the channel to be available for use.

3. If a needle with a memory chip is being used and steps

1 - 2 are unsuccessful, select a new needle for use.

Contact Galil Medical Customer Service to arrange

return of the non-operational needle.

4. The channel may be defective. Do not use this channel.

Move the needle(s) to a different channel. Conduct the

Needle Integrity and Functionality Test again.

Touch screen does not respond

1. The track pad may be used to control the system.
2. The touch screen may be out of calibration. Navigate to

the Configure Settings screen using the track pad and

re-calibrate the touch screen.

3. Turn OFF and restart the system using the power control

knob on the front of the system (Figure 2-1).

USB flash drive is not functioning

The USB flash drive is not

recognized by the system

The USB flash drive is not connected to the proper USB

port. Connect the USB flash drive to the port with the

USB port icon (Figure 2-3).

The USB flash drive is not properly connected to USB

port. Remove the USB flash drive from the designated

USB port on the system. Wait a few seconds and

reconnect the USB flash drive to the designated USB

port.

If the problem persists, try using a different Galil Medical

supplied USB flash drive.

The USB flash drive is faulty. Replace the USB flash

drive with a new Galil Medical supplied USB flash drive.

Содержание Visual-ICE































































































































Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды

BTG Visual-ICE, Руководство пользователя

Результаты поиска

Содержание Visual-ICE

Отзывы:

Похожие инструкции для Visual-ICE

Бренды по названию

Популярные бренды