Brother DCP Series Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 309

background image

5-30

Confidential

1.4.16 Cartridge IC Communication Check (Maintenance mode 57)

<Function>

This function checks the applicable cartridge, color information, destination, size and data
version in the IC chip built in an ink cartridge.

<Operating Procedure>

(1) Enter [5] and [7] in the initial stage of the maintenance mode.

The machine displays "IC_ACT ALL" on the LCD.

To check whether the cartridge is applicable, enter [1].
The machine displays "IC ACT ALL" on the LCD.

To check cartridge color information, enter [2].
The machine displays "IC COL ALL" on the LCD.

To check the destination of the cartridge, enter [3].
The machine displays "IC AREA ALL" on the LCD.

To check the cartridge size, enter [4].
The machine displays "IC SIZE ALL" on the LCD.

To check the data version of the cartridge, enter [5].
The machine displays "IC VER BLACK" on the LCD.

(2) Select the slot number of the cartridge to be checked, using [ ] or [ ].

ALL

: All colors except MAIN

BLACK

: Black

MAGENTA : Magenta
CYAN

: Cyan

YELLOW : Yellow
MAIN

: IC chip in the machine

Note

The color displayed on the LCD indicates not the cartridge color but the cartridge

slot color position.

(3) Press the [Mono Start].

If checking is successfully completed, the LCD shows "OK".
If any error is detected, the LCD shows the corresponding error code as shown below.
Press [Stop] or [X] to return the machine to the initial stage of the maintenance mode.

Error Message

Causes

NG0 to NG99

Failure of IC integrated in the machine

NG100 to NG199

No response from the IC.

• Ink cartridge not loaded

• No IC in the ink cartridge

• IC contact defective

NG200 to NG299

Wrong response result from the IC.

• Cartridge defective

NG300 to NG399

Succeeded in verifying IC, but the information judged as

mismatching

• Loading mistake

«
...
250
251
252
253
254
...
»

Содержание DCP Series






















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCP Series

Бренд: Samsung Страницы: 9

Bixolon SRP-500

Бренд: Samsung Страницы: 27

550N - CLP Color Laser Printer

Бренд: Samsung Страницы: 288

2 COLOR THERMAL PRINTER SRP-275

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 91

WorkCentre Pro 421

Бренд: Xerox Страницы: 4

WorkCentre Pro 412

Бренд: Xerox Страницы: 212

WORKCENTRE PE 220

Бренд: Xerox Страницы: 8

WORKCENTRE PE 220

Бренд: Xerox Страницы: 2

WORKCENTRE PE 220

Бренд: Xerox Страницы: 200

WorkCentre m940

Бренд: Xerox Страницы: 86

Бренд: Xerox Страницы: 24

WorkCentre PE16

Бренд: Xerox Страницы: 201

WorkCentre M24 Color

Бренд: Xerox Страницы: 441

WORKCENTRE C2424

Бренд: Xerox Страницы: 2

WorkCentre M118

Бренд: Xerox Страницы: 5

WORKCENTRE C2424

Бренд: Xerox Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды