Brother DCP Series Скачать руководство пользователя страница 245

Страница: 245 / 309

5-23

Confidential

1.4.10 Sensor Operational Check (Maintenance mode 32)

<Function>

This function checks whether sensors work normally.

<Operating Procedure>

(1) Enter [3] and [2] in the initial stage of the maintenance mode.

The machine sounds 1,100 Hz and 400 Hz tones cyclically through the following
volumes for testing the speaker.

Note

To stop tones from the speaker, press [SET] or [Menu].

If the sensing statuses are as defined below, the LCD shows the 1st sensor group
"DFDRCVRSCCP1****".

(2) Press [Mono Start] to switch to the next sensor group.

If asterisks ("**") appear on the LCD, it means that the corresponding sensor does not
exist on the model.

Given below is the relationship between the LCD indication, sensor name and sensor
status.

*1 For ADF models only
*2 For Ink Cartridge models and MFC-T800W only
*3 For Ink Cartridge models only

Items

shown

on the

LCD

Sensors

Sensing status (display/no display)

Document detection sensor

No document/Document present

Document scanning position sensor

No document/Document present

Document scanner sensor

Cover closed/Cover opened

Registration sensor

No recording paper/Recording paper present

Ink cartridge cover sensor

Cover closed/Cover opened

Purge cam sensor

Origin/Out of origin

Black ink cartridge detection sensor

Cartridge present/No cartridge

Yellow ink cartridge detection sensor

Cartridge present/No cartridge

Cyan ink cartridge detection sensor

Cartridge present/No cartridge

Magenta ink cartridge detection sensor

Cartridge present/No cartridge

Black ink remaining sensor

Ink present/No ink

Yellow ink remaining sensor

Ink present/No ink

Cyan ink remaining sensor

Ink present/No ink

Magenta ink remaining sensor

Ink present/No ink

Head thermistor

Normal temperature/Abnormal temperature

High temperature detector in the complex IC

(for main PCB)

Normal temperature/Abnormal temperature

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды