Brother DCP Series Скачать руководство пользователя страница 181

Страница: 181 / 309

3-73

Confidential

9.15 Ink refill ASSY

Tip

When the Head/carriage unit has not been removed, refer to

"9.3 Head Joint Rubber /

CR Timing Belt / Head/Carriage Unit"

in this chapter to remove the Ink supply tubes from

the Head/carriage unit.

(1) <For Ink tank models only>

If the Ink refill ASSY contains ink, use a Ink extraction syringe to extract the ink.

(2) Remove the Ink supply tubes (4 tubes) from the tube guide on top of the Tube support

plate, take out the sponge, and remove it from the Tube support wire.

(3) Take out the Ink absorber box from the Lower cover.

Tip

When the Main PCB ASSY has not been removed, disconnect the Ink sensor flat

cable from the Main PCB ASSY.

(4) Remove the Ink sensor flat cable from the Lower cover.

(5) <For Ink tank models only>

Slightly slide the Ink refill ASSY to the rear with the Ink refill cap opened, and remove
the four Ink refill caps from the Ink refill ASSY.

(3_131L)

Ink extraction syringe

Ink refill ASSY

Lower cover

(3_132L)

Ink refill caps

Lower cover

Ink refill ASSY

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды