Brother DCP Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 309

background image

ix

Confidential



Federal Communications Commission (FCC) Declaration of Conformity (USA
only)

Responsible Party:

Brother International Corporation
200 Crossing Boulevard
Bridgewater, NJ 08807-0911 USA
TEL: (908) 704-1700

declares, that the products

Product name:

DCP-J100/J105/J132W/J152W/172W/T300/T500W/T700W

MFC-J200/J245/T800W

comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

• (Wireless network only)

This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.



IMPORTANT

• Changes or modifications not expressly approved by Brother Industries, Ltd. could void

the user’s authority to operate the equipment.

• A specific shielded interface cable should be used to ensure compliance with the limits for

a Class B digital device.



RF Exposure Notice (USA or Canada only) (Wireless models only)

• This equipment complies with FCC/IC radiation exposure limits set forth for an

uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines
in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
This equipment should be installed and operated keeping the radiator at least 20cm or
more away from person's body (excluding extremities: hands, wrists, feet and ankles).

«
...
10
11
12
13
14
...
»

Содержание DCP Series






















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCP Series

Бренд: Canon Страницы: 11

imageRUNNER ADVANCE 8085

Бренд: Canon Страницы: 176

Бренд: Canon Страницы: 85

imageRUNNER 5070

Бренд: Canon Страницы: 4

imageRUNNER 5570

Бренд: Canon Страницы: 4

IMAGERUNNER 7095 PRINTER

Бренд: Canon Страницы: 8

IMAGERUNNER 7105

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 58

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 12

imageRUNNER ADVANCE C2020

Бренд: Canon Страницы: 68

imageRUNNER ADVANCE 6055

Бренд: Canon Страницы: 134

Color imageRUNNER LBP5970

Бренд: Canon Страницы: 67

FAXPHONE L170 - B/W Laser - Copier

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 2

imageRunner 1133

Бренд: Canon Страницы: 60

Color imageCLASS MF8280Cw

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 104

imagePROGRAF iPF8300

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды