Brother DCP Series Скачать руководство пользователя страница 136

Страница: 136 / 309

3-28

Confidential

Note

After step (2), perform the following steps below if the Head/carriage unit does not

move.

1) After performing steps (4) to (7), rotate the Pull-in feed roller gear towards you until it

clicks and the Head lock is released.

2) Manually move the Head/carriage unit to the position indicated in the figure.

(4) Unplug the Power cord from the electrical outlet.
(5) Support the Document scanner unit by hand, pull the hook at the rear end of the

Scanner cover damper to the front, and remove the damper from the Document
scanner unit.

Note

When the Jam clear cover is not removed in 9.2, open it first.

(3_020L)

Head/carriage unit

Pull-in feed roller gear

(3_021L)

Hook

Scanner cover support

Scanner cover damper

Document

scanner unit

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды