Brother DCP Series Скачать руководство пользователя страница 148

Страница: 148 / 309

3-40

Confidential

9.4

Document Scanner Unit / ADF Unit (Models with ADF) / Document Cover
ASSY (Models without ADF)

Note

When the Jam clear cover is not removed in 9.2, open it first.

(1) Unplug the CIS flat cable from the Main PCB ASSY. Next, extend the lock arm of the

Upper cover towards you, take out the Flat core and remove it from the CIS flat cable.

Note

After disconnecting the flat cable, check that each cable is not damaged at its end or

short-circuited. Insert the flat cable straightly. After it is inserted, confirm that the cable is
not skewed.

(2) Remove the CIS flat cable from the Cable guide.
(3) Remove the TAPTITE CUP S M3x6 screws, and disconnect the Document scanner

FG wire and ADF FG wire

(3_036L)

CIS flat cable

Document scanner unit

Flat core

Upper cover

Document scanner FG wire

ADF motor harness*1

Document scanning position sensor harness*1

Document detection sensor harness*1

Document scanner motor harness

TAPTITE CUP S M3x6

For models with ADF

ADF

FG wire*1

Cable guide

Lock arm

Main PCB ASSY.

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды