Brother DCP Series Скачать руководство пользователя страница 5

Страница: 5 / 309

Confidential

2.1.1

Document scanning ...................................................................................... 2-3

2.1.2

Printer part .................................................................................................... 2-3

2.2

Document Feeding/Recording Paper Feeding ...................................................... 2-4

2.2.1

Document feeding ......................................................................................... 2-4

2.2.2

Recording paper feeding path....................................................................... 2-4

2.3

Function of Each Sensor/Roller............................................................................. 2-5

2.4

Block Diagram ....................................................................................................... 2-6

2.5

Components .......................................................................................................... 2-7

ERROR INDICATION..................................................................................................... 2-8

3.1

Error Codes ........................................................................................................... 2-8

3.2

Error Messages ................................................................................................... 2-12

3.3

Communications Error......................................................................................... 2-15

TROUBLESHOOTING ................................................................................................. 2-19

4.1

Error Cause and Solutions .................................................................................. 2-19

4.2

Recording Paper Feeding Problems ................................................................... 2-45

4.2.1

Recording paper is not fed from paper tray................................................. 2-45

4.2.2

Two or more sheets of paper fed at a time ................................................. 2-46

4.2.3

Recording paper feeding at an angle .......................................................... 2-46

4.2.4

Recording paper is wrinkling ....................................................................... 2-47

4.2.5

Recording paper jam................................................................................... 2-48

4.3

Print-image Problems .......................................................................................... 2-51

4.3.1

Defective images......................................................................................... 2-51

4.3.2

Troubleshooting by print-image defect........................................................ 2-52

4.4

Software-related Problems .................................................................................. 2-63

4.4.1

Cannot print data......................................................................................... 2-63

4.5

Network Problems ............................................................................................... 2-64

4.5.1

Cannot print through a network connection ................................................ 2-64

4.6

Control Panel Problems....................................................................................... 2-65

4.6.1

No display on the LCD ................................................................................ 2-65

4.6.2

LED does not light up.................................................................................. 2-65

4.6.3

The control panel does not work ................................................................. 2-65

4.6.4

Touch panel inoperative (only for models with a touch panel) .................... 2-65

4.7

Document Feeding Problems .............................................................................. 2-66

4.7.1

Document cannot be fed ............................................................................. 2-66

4.7.2

Document double feeding ........................................................................... 2-66

4.7.3

Document jam ............................................................................................. 2-67

4.7.4

Wrinkles on documents............................................................................... 2-69

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды