Brother DCP Series Скачать руководство пользователя страница 193

Страница: 193 / 309

3-85

Confidential

(2) Release the wiring of the Paper feed motor harness.

(3) Turn the Paper feed motor frame ASSY 45 degrees in the direction of the arrow and

pull it straight up.

It may not be pulled straight up depending upon the position of the black bushing.
Rotate the bushing to the proper position and pull it out.

(4) Remove the two screws of the SCREW BIND M2.6x4 and remove the Paper feed

motor from the Paper feed motor frame.

(3_063L)

Paper feed motor frame ASSY

Bushing

Paper feed motor harness

(3_064L)

Paper feed motor frame

Paper feed motor

SCREW BIND M2.6x4

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды