Brother DCP Series Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 309

background image

3-76

Confidential

9.16 Ink Absorber Box / Ink Absorber Felt (For Ink Refill ASSY)

Note

Do not remove the Ink absorber box unless it needs to be replaced.

(1) Pull out the main Drain tube and Air vent tube from the Ink absorber box.

Note

•

Pinch the end of the main Drain tube with a clip in order to prevent drained ink
from leaking and the machine from getting stained with leaked ink.

•

Do not place a pulled out tube on top of the Main PCB ASSY. If the PCB gets
stained with ink, wipe it off with a clean, dry cloth.

(2) Remove the Ink absorber box from the Lower cover and install the new one

immediately.

Note

If

the Ink absorber box and/or surrounding parts get stained with ink, wipe it off with a

waste cloth.

(3) Take the Ink absorber felt (for the Ink refill ASSY) out of the Lower cover.

Assembling Note

• When connecting the main Drain tube and Air vent tube to the Ink absorber box, connect

the Air vent tube to the upper port and the main Drain tube to the lower port of the box.
Connecting them the other way around will cause a large amount of ink to overflow
during purging.

• Be careful not to connect the main Drain tube and Air vent tube to the Ink absorber box

at an angle. Doing so will cause the tube to get disconnected and leak ink. After
connecting the tubes, make sure that no ink is leaking.

• When the Ink absorber box is replaced (without replacing the Main PCB ASSY), follow

the procedure in

Chapter 4, Section 1.12

to reset the purge count.

It is also recommended to replace the Flushing box and reset the flushing count as
necessary since the flushing count may also be approaching the upper limit.

(3_054L)

View from the right

Main drain tube

Air vent tube

Maintenance unit

Ink absorber box

Lower cover

Do not connect the Main

drain tube at an angle.

Connect it firmly all the

way inside.

Ink absorber felt (for the Ink

refill ASSY)

«
...
182
183
184
185
186
...
»

Содержание DCP Series






















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCP Series

MultiPASS L6000

Бренд: Canon Страницы: 251

MultiPASS C5500

Бренд: Canon Страницы: 24

MultiPASS L6000

Бренд: Canon Страницы: 24

Laser Class 700 Series

Бренд: Canon Страницы: 221

Бренд: Seiko Страницы: 76

Бренд: Konica Minolta Страницы: 404

Бренд: Evolis Страницы: 63

Бренд: Lexmark Страницы: 8

Бренд: Xerox Страницы: 4

Бренд: Kyocera Страницы: 12

Бренд: Konica Minolta Страницы: 46

Бренд: Oce Страницы: 62

Бренд: Xante Страницы: 106

Бренд: Oki Страницы: 76

Бренд: Infotec Страницы: 195

Бренд: Oce Страницы: 227

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды