Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 67

Страница: 67 / 74

6–2

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

Replacing components

CAUTION

Impacts and shocks applied to the shaft end will damage the rotary

encoder and ball bearings!

Drive elements such as pulleys, clutch disks, toothed wheels etc.

may only be assembled or removed by continuously heating up

the drive elements or with a suitable installation or removal tool.

Use the thread in the shaft end.

At least half of motors with an

oil-tight flange on the output side

(oil-

running tight, designs 100, 101) must be submerged in oil. Due to the

high friction, they must never be started dry.

For dry operation, the rotary shaft seal must be removed, however, it

cannot be reinstalled afterwards.

CAUTION

Loss of data!

Interventions in the motor may delete the data of the electronic rat-

ing plate.

Do not dismantle servo motors. Installation work in excess of the

adjustment of the outgoing cable direction must be performed in

the manufacturer’s workshop.

The outgoing direction of all plug-in systems can be changed by releas-

ing the angle flange box.

Do not turn the angle flange box by more than 180

in order to avoid

damaging the connection leads.

CAUTION

Moisture inside the motor.

When tightening the angle flange box, please make sure that the

O-ring is properly seated in the groove of the angle flange box.

Protection standard IP 67 is achieved for the plug-in system only

if the admissible external lead diameters are maintained and the

mating connectors are screwed down to their stop.

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 67 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: