Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 31

Страница: 31 / 74

4–8

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

Displays flash

alternately.

Action

Error

The drive has switched off.

Load contactor is not released

Replace mains connection module

Synchronization error in VM..B,C,D

Check system voltage

Replace supply module

Mains frequency

Mains frequency < 48 Hz or > 62 Hz

Check mains frequency

Overvoltage in DC link

DC link voltage > 800 V

(before: U1 warning display)

Has several meanings on the VMW 180:

DC link overvoltage

Display may also appear if another error

has been cleared with “Drive On”.

Overcurrent in output stage

Driver switched off because of overcur-

rent in output stage

Driver circuit of the output stage defec-

tive

Reduce feedback power

(select longer delay time, reduce brak-

ing current)

Note error message on VM

Error can be cleared with “Drive On”

After “Drive On” error can be cleared by

module RESET

After “Drive On” and module RESET

error can be cleared by toggling 24-V

off/on

Error cannot be cleared. Replace mod-

ule.

Undervoltage in DC link

DC link voltage <400 V

Reduce acceleration power of the axes

(warning display U1 shown before on

VM)

A 2- or 3-phase mains failure may have

been present (previously warning dis-

play U5 on the VM)

Overvoltage in system

System voltage is too high

Check system voltage

Undervoltage in system

System voltage is too low

Check system voltage

Power supply fault

Internal logic supply voltages not in admis-

sible range

Replace module

Fault in external 24 V DC

24 V module supply not within permitted

range

Check 24 V supply at X30 of the supply

module

Check F1 miniature fuse in VM

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 31 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: