Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 33

Страница: 33 / 74

4–10

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

Displays flash

alternately.

Action

Error

The drive has switched off.

Normal operating mode:

ASTS signal in module cross-connection

not cleared properly

Special mode (RSU):
Channel error Drive shutdown

The VM initiates “Drive shutdown”, how-

ever, it cannot transmit this status through

the module cross-connection.

No 24 V supply

The VM has detected that the 24 V supply

is missing in the axis modules.

Check X810 signal cross-connection

Replace module

24 V connection, check 24 V connection

Time delay > (16 sec – S1)

between the shutdown request for an axis

and an additional Emergency Stop com-

mand of the NC/PLC (S1 = rotary switch

on VM, front panel)

Emergency Stop timer on VM defective

Eliminate time overlap between “Drive

shutdown” and “Emergency Stop”

Toggle 24 V off / on or

press RESET

Replace supply module

CPU Test

Microprocessor fault

Replace module

RAM Test

Fault in RAM memory

Replace module

Checksum error

Replace personality module or memory

card

Update Memory Card

Update of memory card was incorrect.

Replace memory card

Watchdog error

Replace module

Error in security test

Replace module

Memory overflow

Replace module

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 33 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: