Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 28

Страница: 28 / 74

Electric Drives

and Controls

4–5

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

4.5

VMA..KR, VMA..B,C,D,F and DM/DS error displays

(without frequency inverter)

For a more detailed analysis, please refer to parameter S-0-0095,

refer to page 4–14, where you will find a lot of specific information

concerning the errors displayed at the drives.

Displays flash

alternately.

Error

The drive has switched off.

Action

Fault in option module

Option module in drive slot is defective.

Check option module for firm seat

Replace option module

Overcurrent

Admissible peak current exceeded.

Reduce load

Select longer braking and acceleration

ramps

Check controller optimization

Check motor

Check application

Real-time error

Error in drive control during commissioning

Restart module

Reduce computer load by DSS-D (e.g.

turn oscilloscope off)

Replace module

Module overtemperature

Excessive heat sink temperature

Check ambient temperature,

increase air supply

Check fan

Reduce load

Motor overtemperature

Motor winding temperature > 145

temperature sensor or sensor cable defec-

tive.

Reduce motor load,

use bigger motor

Check cooling

Check encoder cable

Check application conditions

Ambient overtemperature

Ambient temperature > 55

Check application conditions

Observe derating

Communication error

with SERCOS interface

Communication lost, module jumps

back to phase 0.

with CAN bus

No SYNC message

SERCOS interface:

After phase 2 start up, evaluate type of

error and communication phase in

which the error occurred (S-0-0014).

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 28 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: