manualshive.com logo in svg

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 16 / 74

Поделиться
Скачать
Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 16

Electric Drives

and Controls

2–1

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

Mains connection at the place of installation

2

Mains connection at the place of installation

CAUTION

A reversed phase sequence or winding direction of a line reactor

will destroy the mains connection module.

Please ensure proper wiring.

2.1

Earthing

CAUTION

Inverter modules may only be operated with an earthed neutral

system.

Systems not directly earthed (IT protective system) must not be

used for operation, as air clearances and leakage paths in the

module may be overloaded.

Operation at asymmetrical mains systems (TT protective system,

one mains phase is earthed) is not permissible!

DIN VDE 0100-300 defines mains systems subject to their type of earth

connection.
Accordingly, in an IT protective system, all active parts are separated

from earth, or one point is connected to earth via a resistor.
The exposed conductive parts of an electrical system are either

D

earthed separately, or

D

earthed jointly, or

D

jointly connected to the system earth.

.

Please note the information on earthing in the Servodyn-D EMC

manual, for part no. refer to page 1–9.

DANGEROUS ELECTRICAL VOLTAGE

The only permissible protective measure in accordance with

EN 50 178 is a protective earth connection.

The protective conductor must at least have the same area as the

mains feeder.

Earthing only one end of the DC link when operating by means of

an isolating transformer is prohibited!

Содержание Rexroth Servodyn-D Series











































































Отзывы:

Нет отзывов