Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 29

Страница: 29 / 74

4–6

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

Displays flash

alternately.

Action

Error

The drive has switched off.

Normal operation:

Encoder error

Connection error, short circuit or interrup-

tion of encoder cable.

Encoder, encoder evaluation or electronic

rating plate defective.

Special mode (RSU):

Encoder slip

Noise limiter overload

(because of ex-

cessively long, shielded motor cables)

For details of the fault, refer to

S-0-0095, cf. page 4–14.

For motor encoder and/or external en-

coder:

Check encoder connector

Check encoder cable

Replace motor

Replace module

With RSU:

Check if max. 8 modules per VM

Noise limiter overload if P-0-0047

[

20 V

Trailing error,

Standstill monitoring

Axis moves without traversing command

Check mechanical system

Excessive controller deviation

Drive was not able to follow the setpoint

inputs.

DS modules: Undervoltage in DC link

Compare max. setpoint input to speed

limit (S-0-0091)

Check lag

DS: Check power supply

SERCOS interface

Observe current limit for braking/accel-

eration (P-0-0061, P-0-0062);

Increase acceleration limit S-0-0138;

In mode “Special operation” adjust the

setpoint input of the NC to the setup

speed P-0-0012.

Position limit exceeded

The setpoint input leads to an axis position

outside the traversing range.

Check position limit parameters

S-0-0049 and S-0-0050

Check setting of software limit switches

Normal operation:

Maximum speed exceeded (channel 1)

The speed limit value S-0-0091 was ex-

ceeded.

Special operating mode (RSU):

Deviation from Safe Standstill

(channel 1)

The angle of rotation limit value

P-0-0022 was exceeded.

Special mode with acknowledgement

(RSU):

Deviation from Safe Speed

(channel 1)

The speed limit value P-0-0012 was ex-

ceeded.

Observe speed limit

Observe sequence of operations

Check enable signals

Check control circuits

Clear error by “Reset Diagnostics class

1 error”

Check whether the fan on the bot-

tom side of the module has failed.

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 29 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: