Bosch Rexroth Servodyn-D Series Скачать руководство пользователя страница 6

Страница: 6 / 74

Electric Drives

and Controls

1–1

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

Safety Instructions

Safety Instructions

Please read this manual before commissioning the Servodyn-D drives.

Store this manual in a place to which all users have access at any time.

1.1

Intended use

This manual contains information required for the intended use of this

product.

The described low-voltage motors are intended for use in

commercial

or industrial systems

. They comply with the harmonized standards of

the VDE 0530/EN 60034 series. Their use in potentially explosive atmo-

spheres is not admissible unless expressly permitted by additional

instructions.

Air-cooled designs are rated for ambient temperatures ranging between

–20 to +40

C, and an operating altitude of

1000 m above sea level.

Rating plate specifications deviating from this standard must be strictly

observed. Conditions at the operating site must correspond to all specifi-

cations stated on the rating plate.

Low-voltage motors comprise

components

intended for integration into

machines as contemplated by the EU Declaration of Conformity, as de-

fined by Machinery Directive (98/37/EC, 98/79/EC). Before putting the

motors into operation, ensure that the machine the motors are to be

installed in meets the stipulations of the Machinery Directive (note also

EN 60204-1).

The drive inverters described

have been developed, manufactured, tested and documented in

compliance with the safety standards. These products normally pose

no danger to persons or property if they are used in accordance with

the handling stipulations and safety notes prescribed for their config-

uration, mounting, and proper operation.

comply with the requirements of

the EMC Directives (89/336/EEC, 93/68/EEC and 93/44/EEC)

the EMC product standard EN 61800-3 + A11

the Low-Voltage Directive (73/23/EEC)

the harmonized standards EN 50178 (VDE 0160) and

EN 60146-1-1 (VDE 0558-11)

are designed for operation in industrial environments, i.e.

no direct connection to public low-voltage power supply,

connection to the medium- or high-voltage system via a trans-

former.

In residential environments, in trade and commerce as well as small

enterprises class A equipment may only be used if the following warn-

ing is attached:

Содержание Rexroth Servodyn-D Series











































































Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы:

Bosch Rexroth Servodyn-D Series, Руководство по обслуживанию, Страница: 6 / 74

Результаты поиска

Содержание Rexroth Servodyn-D Series

Отзывы: